Motive-RC MR4SM 2.4G HV S-FHSS Mini Receiver for Futaba

Description

*Compatible with Futaba 3PV 4PLS 4PX 4PV 4PM 10PX

MOTIVE-RC’s S-FHSS compatible mini receiver. This production can supply enhancement smooth drive with FUTABA S-FHSS link.

Compatibility:

MOTIVE-RC 2.4GHz S-FHSS Compatible mini Receiver is designed to use with FUTABA S-FHSS 2.4GHz transmitters, such as surface system T3PV, 4PLS, T4PX, T4GRS, T4PM, T4PV, T7PX, T10PX or air system T4YF, T6J, T6K, T8J, T10J, T14SG, T18MZ, T18SZ under S-FHSS protocol mode.

Feature:

• 4ch servo channels on CH1~CH4
• S.BUS output(on the back of the board) support expanding servo channels.
• Normal mode and High Speed mode.
• Support Fail-safe function on all channels

Specifications:

• Model Type: RC Car
• Operating Current: 20mA max and 10mA under linked
• Antenna: Tower antenna or Short antenna
• Operating Voltage:  3.3~8.5V(1S~2S LiPo)
• Operation temperature: – 10~70 degC
• Weight: 1.2g
• Size: 18.8×12.5×6 mm
• Latency: 6.8ms(High Speed mode) or 13.6ms(Normal mode)

The Comparison of “Normal Mode” and “High-Speed Mode” Signals:

Bind procedure:

1. Connect the battery to the receiver while pressing receiver’s BIND button.
2. Turn on the S-FHSS transmitter, leave it 0.5M~1M away the receiver.
3. Red LED light on and Green LED off when searching signals, and turn to Green LED light on and Red LED off indicate         bind is succeeded.
4. Remove the power from the receiver, reconnect the power cable to the receiver.
5. Check to make sure that the transmitter and receiver are working as expected, if there are any issues or unexpected operation follow the steps above to bind again.

Fail-safe setting:

MR4SM set failsafe on the S-FHSS transmitter just like the operation of the FUTABA receivers if the feature exist. We highly recommend you set failsafe feature while driving your models. An example of a useful failsafe setting would be to shut down the model’s throttle, so that it does not drive away uncontrolled.

High Speed/ Normal mode switch guide:

The “Normal mode” accepts any type of servos or the peripheral. The “High Speed mode” only accepts the digital servos, including BLS series, and most peripheral equipment such as the brushless ESC. Please pay special attention to the information contained within this manual and transmitters manual in order to have a pleasant running experience.

If your receiver has been linked with your transmitter, please power off your transmitter. When your receiver’s LED light red, press and hold the button on the receiver for more than 6 seconds but no longer than 10 seconds. Release the button and you will see the green LED blinking slowly. Now press the button again, and the receiver will first blink the red LED and then turn off, followed by the green LED blinking. (Pay attention to the speed of the green LED flashing, as this indicates the receiver’s working mode). When the green LED blinks slowly, it means the receiver has switched from high-speed mode to normal mode; when the green LED blinks quickly, it means the receiver has switched from normal mode to high-speed mode. After about 6 seconds, the green LED will turn off, and the red LED will stay on, indicating that the mode switch is complete.

Note: If you want to reset the receiver to normal mode, you can rebind the receiver to the remote control.

LED status indicated under normal working status:

Package included:

1 x MR4SM Receiver

4 x 1.5mm 3Pin JST plug cables (for servo channels)

1 x 2.54mm 3Pin JR plug cable (for sbus pad)

Additional information